Wavlink range extender helps in boosting and broadcast the existing wireless signal to hard-to-reach areas of your home. You can enjoy seamless internet access on every device in every nook and corner of the home by getting the Wavlink setup done. However, a flashing red light on the Wavlink extender can ruin this smooth and happy experience. Are you nodding your head in agreement with us? Well, then your time to worry is over. Head towards happier times by walking through this guide and kick out the flashing red light issue with your Wavlink range extender.
Troubleshooting Wavlink Extender Red Light Problem
Find the most tried and tested troubleshooting hacks in this article and fix the issue on your own without having to contact Wavlink tech support.
Hack 1: Reboot the Extender
What comes to mind first when your technical device begins giving trouble? Yes? You are right. Power it off. Do the exact thing with your Wavlink range extender now. Rebooting flushes out minor technical issues with devices. To reboot, follow this process:
- Turn off the Wavlink wireless range extender.
- Unplug it from the power socket.
- Detach every connecting cable from the device.
- Let it rest for a while.
- Attach all the cables back.
- Plug it into the power socket again.
- Turn the power supply on.
What do you notice? Has the issue been fixed? Is it still flashing red light? Yes? Move to the next hack then.
Hack 2: Pull the Devices Closer
How far is your Wavlink range extender from the host router? Perhaps the distance between the devices is more which is why the light is flashing red as the extender is unable to receive the signal from the router. What to do? Move the extender closer to the router. While doing so, make sure that you do not reduce the distance to the level that the device’s signal gets interfered with. Thus, choose an appropriate distance between them. The devices should be neither too close nor too far.
Hack 3: Check Wiring
In case there is a wired connection between the extender and the router, then take a look at the Ethernet cable that is being used to connect them. Is it worn out? Does it contain deep cuts on it? Replace it immediately if you find it faulty. Has this resolved the red light issue? Proceed to the next hack if the issue persists.
Hack 4: Verify Power Socket
What if the Wavlink extender is not connected to a reliable power source? The possibility is that the power socket is damaged. Go ahead and check it now. The flashing red light on the Wavlink extender could also be due to fluctuating power supply. You can also use an alternative power socket to connect the extender. If the issue gets fixed, then put a full stop to troubleshooting here, or else get to the next hack.
Hack 5: Get Rid of WiFi Interference
WiFi interference can also lead to issues with the Wavlink range extender thereby giving red light warning. In such a situation, verify if some devices or appliances that radiate radio or electromagnetic waves are placed near the Wavlink extender. Such devices can be microwave ovens, baby monitors, cordless phones, walkie-talkies, Bluetooth speakers, etc. Move the extender away from any such device.
Hack 6: Avoid Signal Obstruction
Make sure that you do not place the Wavlink range extender at a place where it is difficult to access its network. For instance, you will find difficulty in accessing the signal of the extender that is placed in a corner, attic, basement, behind a cupboard, etc. Apart from this, heavy mirrors, concrete walls, large water bodies, etc. can also block or obstruct the signal. Thus keeping these points in mind, move the extender to a better location.
Hack 6: Update Firmware
If you haven’t updated your Wavlink extender in recent times, then this is the possible culprit for the red light. Simply access the Wavlink login page and check if the firmware update is pending. If yes, then simply install the firmware and check if the issue has been fixed or not.
Hack 7: Reset Device
This remains the last resort in case the issue seems adamant to leave. What will happen by resetting? This will erase the personalized settings from the extender and reload the factory settings on it. This will also help to kick out any technical error that is causing the red light issue. To reset, simply press the Reset button on the Wavlink extender.
The Closing Note
After resetting, access the wifi.wavlink.com setup wizard and complete the setup and begin accessing the Wavlink extender network. Here we put an end to our guide about troubleshooting the Wavlink extender red light issue. We are very hopeful that the aforementioned hacks will help you out to get rid of the Wavlink range extender red light issue.
